維特銳集團李工經銷易福門阿托斯柱塞泵，種類齊全，價格優勢。歡迎詢價對比~

PVPCX2C-CH-3046/5029/5S-IX
PVPCX2C-C-3046/5029/5S-IX
PVPCX2C-R-3046/5029/5S-IX
PVPCX2C-L-3046/5029/5S-IX
PVPCX2C-LW-3046/5029/5S-IX

PVPCX2C-CH-4046/5029/5S-IX
PVPCX2C-C-4046/5029/5S-IX
PVPCX2C-R-4046/5029/5S-IX
PVPCX2C-L-4046/5029/5S-IX
PVPCX2C-LW-4046/5029/5S-IX

PVPCX2C-CH-5046/5029/5S-IX
PVPCX2C-C-5046/5029/5S-IX
PVPCX2C-R-5046/5029/5S-IX
PVPCX2C-L-5046/5029/5S-IX
PVPCX2C-LW-5046/5029/5S-IX

PVPCX2C-CH-3046/3073/5S-IX
PVPCX2C-C-3046/3073/5S-IX
PVPCX2C-R-3046/3073/5S-IX
PVPCX2C-L-3046/3073/5S-IX
PVPCX2C-LW-3046/3073/5S-IX

PVPCX2C-CH-4046/3073/5S-IX
PVPCX2C-C-4046/3073/5S-IX
PVPCX2C-R-4046/3073/5S-IX
PVPCX2C-L-4046/3073/5S-IX
PVPCX2C-LW-4046/3073/5S-IX

PVPCX2C-CH-5046/3073/5S-IX
PVPCX2C-C-5046/3073/5S-IX
PVPCX2C-R-5046/3073/5S-IX
PVPCX2C-L-5046/3073/5S-IX
PVPCX2C-LW-5046/3073/5S-IX

PVPCX2C-CH-3046/4073/5S-IX
PVPCX2C-C-3046/4073/5S-IX
PVPCX2C-R-3046/4073/5S-IX
PVPCX2C-L-3046/4073/5S-IX
PVPCX2C-LW-3046/4073/5S-IX

(1)檢查柱塞有無傷痕和銹蝕現象，必要時應更換新品。(2)檢查柱塞副配合情況。將柱塞端頭插人柱塞套內，傾斜約60°，若柱塞能在自身作用下緩慢地下滑為配合良好。(3)檢查柱塞副的密封性。用手握住柱塞套，兩個手指堵住柱塞頂端和側面的進油口。用另一只手拉出柱塞，感到有較大的吸力，放松柱塞立即縮回原位，表明柱塞副密封良好，否則應更換柱塞副。(4)檢查出油閥副減壓環帶是否磨損有臺階或傷痕現象，必要時應予以更換。(5)檢查出油閥副的配合情況。用手指堵住出油閥下孔，用另一手指將出油閥輕輕向下壓，當手指離開出油閥上端時，它能自動彈回原位，表明出油閥副密封良好，否則應更換出油閥副。(6)檢查挺柱體。噴油泵體和挺柱體之間的標準間隙為0～0.03mm，如超過0.2mm ，則應更換零件。(7)檢查柱塞凸緣和控制套的凹槽之間的間隙，應為0.02～0.08mm，如超過0.12mm，必須更換控制套。

以上信息版權歸上海維特銳所有，如需詳細了解請點擊：意大利atos柱塞泵系列